Launch offer — valid today only

📄 Digital book in PDF · read it on your phone or print it

The Boiler Room and the Fifth Class Exam, Drawn One Topic on Every Page

Boilers in cross-section, gauge vs absolute pressure, safety valves, the gauge glass, feedwater, the gas burner train, purge and flame safeguard, lockout. Every topic gets its own page: first the drawing, then what you need to remember. 66 illustrated pages.

GET THE BOILER ROOM, DRAWN

🔒 Secure checkout · PDF by email · 30-day guarantee

Every topic, its own pageEach fitting, valve and sequence drawn, with the explanation right beside it
66 illustrated pages8 parts, from what the Fifth Class ticket lets you do to the one-page review the night before
Up-to-date sourcesInterprovincial Fifth Class syllabus, CSA B51 and your provincial regulator's rules
PDF by emailFormat

Look Inside the Book

Every page has one big drawing and a box with the pressures, temperatures and steps you need to know:

Steam: vapour out, condensate back. Hot water: closed loop with an expansion tank
Steam: vapour out, condensate back. Hot water: closed loop with an expansion tank
High pressure: steam above 103 kPa, hot water above 1,100 kPa or 121 °C
High pressure: steam above 103 kPa, hot water above 1,100 kPa or 121 °C
1000 kPa gauge = about 1101.3 kPa absolute
1000 kPa gauge = about 1101.3 kPa absolute
Furnace = pass 1, each tube set adds one; dry back vs wet back turnaround
Furnace = pass 1, each tube set adds one; dry back vs wet back turnaround
Risers carry lighter hot water up, downcomers bring denser water down; a blocked tube overheats
Risers carry lighter hot water up, downcomers bring denser water down; a blocked tube overheats
Open drain → close water → open water, close steam → open steam → close drain.
Open drain → close water → open water, close steam → open steam → close drain.
Manual shutoff → regulator → low gas switch → two safety shutoff valves → high gas switch → firing rate valve → burner.
Manual shutoff → regulator → low gas switch → two safety shutoff valves → high gas switch → firing rate valve → burner.
One-page review: 101.3 kPa, 103 kPa, 1,100 kPa, 121 °C, 4.19, 2,257, burner sequence, extinguisher classes.
One-page review: 101.3 kPa, 103 kPa, 1,100 kPa, 121 °C, 4.19, 2,257, burner sequence, extinguisher classes.

Swipe to see more →

These are real pages from the book. The table of contents is the full one: 8 parts and 62 topics.

The Problem Isn't You. It's How It Was Explained.

You're at the kitchen table after a long shift, with one practice question in front of you: 1000 kPa on the gauge. What's the absolute pressure?

The textbook gives you two paragraphs on atmospheric pressure, kPa gauge and kPa absolute. You read them, nod, and by the next question you can't remember which one gets added to which.

1000 kPa gauge = about 1101.3 kPa absolute

In the book it's one page: a gauge reading zero in open air, the 101.3 kPa of atmosphere drawn underneath it, and 1000 kPa gauge = about 1101.3 kPa absolute worked out in a box.

Same with the rest: the gauge glass blowdown, the gas burner train, counting passes in a firetube, the low water fuel cutoff. Each one has its own page.

So when the question comes, on the exam or from the shift engineer, you picture the drawing and do the conversion without reopening the textbook.

COMPARE FOR YOURSELF

Same Topic, Two Ways to Study It

THIS
  • The textbook: line after line
  • Fittings and valves explained only in words
  • You walk into the exam still unsure
The boiler plant comprises numerous interrelated components, which may be classified according to function. Water-side components include the feedwater pump, feed check valve, feed stop valve, gauge glass, try cocks, low water fuel cutoff and bottom blowdown valves. Steam-side components include the main steam stop valve, non-return valve, safety valve and pressure gauge with siphon. The fuel and air system comprises the burner, gas train, forced draft fan and stack, while the operator is further required to understand the function and location of each safety and limit control.
FOR THIS
  • The whole boiler room in one labelled drawing
  • The 40 names sorted: water, steam, fuel and air, safety
  • You see it and it makes sense
High pressure: steam above 103 kPa, hot water above 1,100 kPa or 121 °C
CONTENTS

Take a Look at the 8 Parts and 62 Topics

The ticket and the plant map, pressure and heat, boilers inside out, fittings and safety devices, feedwater and water treatment, combustion and burner controls, plant safety, and operating practice with exam review: 66 pages, all illustrated

IThe Ticket and the Plant Map · pp. 5-10
  1. What a Fifth Class ticket lets you do
  2. How the exam works
  3. The plant map: one loop you will see on every page
  4. Steam plant vs hot water plant
  5. Low pressure vs high pressure boilers
  6. The boiler room in one picture
IIPressure, Temperature and Heat · pp. 11-18
  1. Pressure is force on an area
  2. Gauge vs absolute pressure
  3. Vacuum and the condensate side
  4. Temperature scales and conversions
  5. Sensible heat vs latent heat
  6. Saturation: pressure sets the boiling point
  7. Wet, dry saturated and superheated steam
  8. Reading a steam table in four steps
IIIBoilers Inside Out · pp. 19-26
  1. Firetube boiler in cross-section
  2. Counting passes in a firetube boiler
  3. Watertube boiler in cross-section
  4. Natural circulation: why the water moves
  5. Cast iron sectional and electric boilers
  6. Heating surface and boiler rating
  7. Boiler stays, tubes and how they fail
  8. The nameplate: what to read first
IVFittings and Safety Devices · pp. 27-35
  1. Safety valve: pop open, blow down, reseat
  2. Safety valve vs relief valve
  3. The pressure gauge and its siphon
  4. Gauge glass and try cocks
  5. Blowing down the gauge glass, step by step
  6. Low water fuel cutoff
  7. Bottom blowdown valves: which first
  8. Main steam stop, non-return and feed check valves
  9. Hot water boiler fittings
VFeedwater, Water Treatment and Steam Distribution · pp. 36-43
  1. The feedwater path, from tank to drum
  2. Why water must be treated
  3. Softeners and ion exchange
  4. Deaerator: removing the oxygen
  5. Boiler water testing on rounds
  6. Feed pumps and NPSH
  7. Steam traps: three families
  8. Water hammer and line drainage
VICombustion and Burner Controls · pp. 44-51
  1. The combustion triangle and the three Ts
  2. Excess air: not too little, not too much
  3. Natural gas burner train
  4. Fuel oil firing basics
  5. Draft: forced, induced, natural, balanced
  6. Purge before every light-off
  7. Flame safeguard: the burner's sequence
  8. Operating controls vs limit controls
VIIPlant Safety and Auxiliary Systems · pp. 52-58
  1. Lockout and isolation
  2. Confined space: boiler drum and furnace entry
  3. WHMIS and chemicals in the boiler room
  4. Fire extinguisher classes
  5. Electricity basics for operators
  6. Air compressors and receivers
  7. Heating systems and basic refrigeration
VIIIOperating Practice and Exam Review · pp. 59-66
  1. Boiler startup in the same order every time
  2. Normal operation and the daily round
  3. Taking a boiler off line and laying it up
  4. The logbook: what an inspector wants to see
  5. Emergencies: low water and flame failure
  6. Common mistakes in theory and on rounds
  7. How to read a multiple-choice question
  8. The night before: one-page review

One Page, One Topic, All Clear

Think of it this way:

You're on your round and the shift engineer tells you to blow down the gauge glass. Three valves, and the order matters.

You open the book to that page and see the glass drawn with its steam valve, water valve and drain, every move numbered, from opening the drain to closing it again.

Risers carry lighter hot water up, downcomers bring denser water down; a blocked tube overheats

Same with the gas burner train, purge before light-off, the safety valve, the deaerator and lockout: each one on its own page.

Fifth Class Power Engineer Illustrated is 8 parts and 66 illustrated pages, every topic drawn, with a one-page review for the night before at the end.

What you see drawn, you don't have to memorize.

What's Inside Fifth Class Power Engineer Illustrated:

Ipp. 5-10

The Ticket and the Plant Map

What the Fifth Class ticket lets you do, how the exam works, steam vs hot water, low vs high pressure and the plant map you'll see on every page.

IIpp. 11-18

Pressure, Temperature and Heat

Force on an area, gauge vs absolute, vacuum, temperature conversions, sensible and latent heat, saturation and reading a steam table in four steps.

IIIpp. 19-26

Boilers Inside Out

Firetube and watertube boilers in cross-section, counting passes, natural circulation, cast iron and electric boilers, stays, tubes and the nameplate.

IVpp. 27-35

Fittings and Safety Devices

Safety and relief valves, the pressure gauge and its siphon, gauge glass and try cocks, low water fuel cutoff, blowdown valves, stop and check valves, hot water fittings.

Vpp. 36-43

Feedwater, Water Treatment and Steam Distribution

The feedwater path, why water is treated, softeners, the deaerator, boiler water tests on rounds, feed pumps and NPSH, steam traps and water hammer.

VIpp. 44-51

Combustion and Burner Controls

The combustion triangle, excess air, the natural gas burner train, fuel oil, draft, purge, the flame safeguard sequence, operating vs limit controls.

VIIpp. 52-58

Plant Safety and Auxiliary Systems

Lockout and isolation, confined space entry, WHMIS, extinguisher classes, electricity basics, air compressors, heating and basic refrigeration.

VIIIpp. 59-66

Operating Practice and Exam Review

Startup in the same order, the daily round, taking a boiler off line, the logbook, low water and flame failure, common mistakes, multiple-choice tips and the one-page review.

At the end of the book: Exam-style practice questions, the most common mistakes and a one-page review for the night before.

Plus: 2 Free Books

Fifth Class Exam-Style Practice Questions

BONUS 1: «Fifth Class Exam-Style Practice Questions»

Value on its own: US$ 17.90

Multiple-choice questions in the style of the certificate exam, each answer explained with a small drawing, so you find your weak spots before exam day.

Boiler Room Mistakes: 15 Before & After Pages

BONUS 2: «Boiler Room Mistakes: 15 Before & After Pages»

Value on its own: US$ 14.90

The most common mistakes on rounds and in the theory, drawn wrong and then right, so the correct picture is the one you remember.

Fifth Class Power Engineer Illustrated with 2 Free Books

  • Fifth Class Power Engineer Illustrated: 66 illustrated pagesUS$ 63
  • BONUS 1: Fifth Class Exam-Style Practice QuestionsUS$ 17.90
  • BONUS 2: Boiler Room Mistakes: 15 Before & After PagesUS$ 14.90
  • High-resolution PDF to printIncluded
Total value US$ 95.80
YOUR PRICE:
US$ 27
You save US$ 68.80
YES, I WANT FIFTH CLASS POWER ENGINEER ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

Secure purchaseEncrypted payment30-day guarantee

PDF by email: We email you Fifth Class Power Engineer Illustrated as a PDF, together with the two free books. It's a single payment: no installments, no extra charges.

Who This Book Is For

You're studying for your Fifth Class

You're studying for your Fifth Class

Every syllabus topic on its own page, so after a shift you study one drawing, not a whole chapter.

Your exam date is close

Your exam date is close

The common mistakes, the one-page review and the exam-style questions show you your weak spots before you write the provincial exam.

You already work in the plant

You already work in the plant

Building operator, maintenance or oil and gas: the startup order, the daily round and the gauge glass blowdown drawn, printed and on hand during your shift.

Everything You Get Today

US$ 95.80US$ 27
YES, I WANT FIFTH CLASS POWER ENGINEER ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

30DAYS
GUARANTEE

30-Day Guarantee

Try Fifth Class Power Engineer Illustrated for 30 days, bonus books included.

We refund everything if the file won't open, if the book isn't what you see here, if you were charged twice or if the email doesn't arrive. Just email us.

You pay once. No subscriptions.

Frequently Asked Questions

Is it for me if I've been out of school for 20 years?

Yes. It's written for working adults: one topic per page, the drawing first and the key numbers in a box. No academic padding.

Does it work for my province (Alberta, BC, Saskatchewan, Ontario)?

It's based on the interprovincial Fifth Class Power Engineer syllabus, CSA B51 and the rules of provinces that follow it, such as Alberta (ABSA), BC (Technical Safety BC) and Saskatchewan (TSASK). Not every province issues a Fifth Class certificate, so check with your regulator (in Ontario, TSSA) that your exam follows the interprovincial syllabus. Set pressures, intervals and exam format are flagged so you can confirm them for your province.

Is it official material?

No. It's an independent illustrated study book. It isn't published, approved or endorsed by any regulator, standards body or school, and it doesn't give you a ticket, a certificate or firing time: only your provincial regulator's exam and requirements do that.

Does it replace my course or textbook?

No. It's the drawn companion for reviewing and understanding. It doesn't replace your course, your site procedures or your chief engineer.

Are the practice questions the ones on the exam?

No. They're written for this book in multiple-choice style. They aren't official questions from any exam.

When and how do I get it?

The book and the 2 bonus books arrive as PDFs by email, at the address you enter at checkout.

Do I have to pay every month?

No. It's a one-time payment.

Can I have it on paper?

Yes. It's a printable PDF: print the whole book or just the pages you want on hand at work.

How does the refund work?

You have 30 days. We refund everything if the file won't open, if the book isn't what you see on this page, if you were charged twice or if the email doesn't arrive: just email us.

Before You Close This Page

No more rereading a chapter that's gone by morning.

Gauge vs absolute: you see it drawn and that's it.

You walk into the exam knowing where everything sits in the plant.

Drawings make studying faster.

The book is right below.

One-time payment: US$ 27 · Guarantee: 30 days · PDF by email

YES, I WANT FIFTH CLASS POWER ENGINEER ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.